GT4Z-3F988-B 2011-2015 Ford Edge Explorer Shift Park Detent Switch Shifter - New Genuine Ford Part

2011-2014 Ford Edge 11-15 Explorer Shift Park Detent Shifter Switch - See Important Notes

Vendor: Ford
Availability: In Stock
$ 67.60
$ 67.60
Same-Day Shipping
Get same-day shipping on most orders placed by 2pm Central Time.
GT4Z-3F988-B 2011-2015 Ford Edge Explorer Shift Park Detent Switch Shifter - New Genuine Ford Part

2011-2014 Ford Edge 11-15 Explorer Shift Park Detent Shifter Switch - See Important Notes

$ 67.60

2011-2014 Ford Edge 11-15 Explorer Shift Park Detent Shifter Switch - See Important Notes

$ 67.60

Important Note: 

Fits the 2011-2014 Edge with a push-button start only.

Fits 2011-2015 Explorer or MKX with a push-button start only.

If you have to insert a key and turn it to start the vehicle this will not be the correct part. 

Your Shifter must be on the floor for this to be correct. 

Issue: Floor shift selector lever and push button start models may exhibit a Shift To Park message, Transmission Not In Park message displayed while the shifter is in park position, or unable to remove the integrated keyhead transmitter (IKT), or a discharged battery due to the Shift to Park light remaining illuminated.

Installation Instructions:

Tools Needed:

  • Socket Set
  • Torx bit set
  • Screwdriver
  • Pry tool

Skill Level: Intermediate

Installation Time: Approximately 1-2 hours

Note: Before starting the installation, ensure that the battery is disconnected to prevent accidental airbag deployment.

  1. Use a pry tool to carefully remove the center console trim covers to expose the shift park detent switch shifter assembly.
  2. Locate the wiring harness connector for the shift park detent switch shifter assembly and disconnect it by pressing down on the locking tab and pulling the connector away from the assembly.
  3. Use a socket set and Torx bit set to remove the bolts and screws securing the shift park detent switch shifter assembly to the center console.
  4. Carefully remove the old shift park detent switch shifter assembly from the center console.
  5. Install the new Genuine Ford shift park detent switch shifter assembly by aligning it with the mounting points on the center console and securing it with bolts and screws.
  6. Reconnect the wiring harness connector to the back of the new shift park detent switch shifter assembly.
  7. Reinstall the center console trim covers by snapping them back into place.

It is important to note that this installation requires intermediate-level skills and should not be attempted by individuals with limited automotive knowledge. The job can take approximately 1-2 hours to complete, depending on the installer's skill level and familiarity with the vehicle. Always make sure to reconnect the battery after completing the installation.

 

 

 

Easy No Hassle Return Information

Simply return your part in the exact same condition and packaging that you received it in within 30 days for a full refund of the purchase price of the part, minus the original shipping charges. You don't even have to contact us. Just be sure the read the requirements below and follow the instructions at the bottom of this page.

 

What can not be returned:

 

Any part that does not have all of the original packaging with the attached manufacturer part number label.

Believe it or not, this is super important! Don't throw away the packaging.  Manufacturers wont accept returns on a part without the genuine OEM Packaging, so we wont be able to credit you. (Even if the part is brand new with no packaging, we would have to return it to you).

 

 

We also cannot accept your return if: 

  • You have installed or attempted to install or disassemble the part
  • You have painted the part.
  • You have broken the part.
  • You have lost the original packaging.
  • You have gotten the part wet, or the part has greasy fingerprints.

 

Electrical Parts.

Electrical parts can only be returned if they have not been installed, programmed, or plugged in. If the part shows signs, of an attempted install we will be unable to accept your return.

 An electrical part is any part that plugs in, contains a switch, sensor, circuit board or electrical wiring.

 

Here are 2 examples of what a part number label looks like. if you Do not have the packaging with your part number similar to this we can't accept your return

 

 

 

 

HOW TO RETURN

NOTE: YOU DO NOT HAVE TO CONTACT US TO MAKE A RETURN.

  

  1. Make sure you have all the original packaging with part number labels as shown above.

 

  1. Please be sure to put a copy of the receipt or order confirmation email in the box.

 

  1. Go to the post office or UPS Store where you can pay them for the postage directly. We reccomend using UPS. The US postal service is slow and unreliable in our area,

 

Make sure you get a tracking number before you leave the store. Buying insurance is usually a good idea. We cannot be responsible for any return that is lost or damaged in transit.

 

SEND YOUR PACKAGE BACK TO THE FOLLOWING ADDRESS.

 

Conquest Auto Parts

1320 HWY 3 SOUTH, SUITE C4

 LEAGUE CITY, TX 77573

 

What Happens Next?

 

Check your tracking number to see when we receive your return.

Once we receive your return we will inspect it and issue a credit to your original payment method usually the same or next business day. We will send you an email or text once the credit has been issued. 

It is important to note that even though we issue the credit, your bank who manages your credit card may hold your refund for up to 7 days before posting it to your account. This is done by your bank, and is standard procedure no matter where you buy from online. You can contact your bank for their policies.

 

Refunds

  • You should receive your credit within 3-5 Business days of the date we receive the return.
  • Credit will be applied to the same credit card or account used to purchase the part.
  • Your Credit will be for the purchased item only. We do not refund the original shipping charge.

Related Products

Recently Viewed Products